G&P Geotechnics

Research and Development

  • List of Completed R&D Project
  • Spreadsheet for Digitising Caquot & Kerisel Design Table for earth pressure coefficients
  • Spreadsheet for Review on Bearing Capacity calculation based on Eurocode 7
  • Spreadsheet for compile and review on typical details of RC Wall that had been used in projects
  • Spreadsheet to carry out manual calculations based on the confirmed design approaches and basis for review
  • OP for soil nail input in SLOPE W
  • OP for individual pad design to justify on nail head load
  • OP for grid beam design
  • Spreadsheet for grid beam design
  • Spreadsheet for back-calculated Bending moment Diagram from Deflection Profile
  • Spreadsheet for temporary ground anchor design
  • Spreadsheet for shear reinforcement for circular section
  • Spreadsheet for wall stiffness EI for hard/hard secant pile wall
  • Spreadsheet for reinforcement design for hard/hard secant pile wall.
  • Spreadsheet for steel decking design based on area load
  • OP for design of dewatering/recharge wells and design of groundwater control based on CIRIA C515 & design of dewatering/recharge wells
  • Spreadsheet for micropile design
  • Spreadsheet for PVD design
  • Compilation on settlement monitoring results
  • Technical Manual for SI Planning of Tunnelling Works
  • Checklist for method of logging for SI boreholes for tunnel project
  • Spreadsheet for interpretation of Working Pull Out Test
  • Spreadsheet for Lateral Pile (Elastic only)
  • Spreadsheet for automation in Grapher Plotting
  • Spreadsheet for Workload Monitoring
  • Technical Paper on Taiping Portal
  • Design of filter
  • Spreadsheet for AGPC for Bored Pile V 1.2
  • Spreadsheet for AGPC for Caisson Pile V1.0
  • Spreadsheet for Static Load Test Using Kentledge Method V1.4
  • Database of Accreditted Contractor
  • OP for Tender Interview Checklist for Earthworks (TQ)
  • Spreadsheet to check and verify RC wall manual calculations based on the confirmed design approaches
  • Spreadsheet to extract Caquot & Kerisel’s coefficients
  • Spreadsheet for RC Wall Design
  • Spreadsheet for individual pad design
  • Standard drawing for compilation of soil nail head details (shotcrete facing, individual pad & grid beam)
  • OP / TM for deep excavation design
  • Spreadsheet for temporary ground anchor design (steel bracket design)
  • Spreadsheet for interpretation of odeometer test results
  • Spreadsheet for consolidation settlement to consider buoyancy effect
  • Revised RS Wall design Spreadsheet to consider ground water level
  • Spreadsheet for building damage assessment & Building Condition Survey
  • Spreadsheet for Cost Estimation for RC wall (AD028)
  • Parametric Study for Pile Raft Analysis (Pile Spacing = 4.0m, Raft = 0.4m thk)
  • Parametric Study for Pile Raft Analysis (Pile Spacing = 6.0m, Raft = 0.4m thk)
  • Standardize BOQ for Rubble Wall
  • Spreadsheet for reduction of existing pile capacity due to tunnelling
  • Spreadsheet for bored pile design
  • OP / TM for compilation of instrumented pile load test for bored pile for interpretation of ks value
  • List of On-going Projects
  • Sensitivity study on soil parameters for slope stability
  • OP / TM for strutting design
  • Spreadsheet for tension pile design
  • Spreadsheet for steel decking design based on HA/ HB loading
  • Spreadsheet for CIU test interpretation to incoporate MSR and MDS
  • Technical manual for Guideline on Tunnel Instrumentation
  • Spreadsheet for Tunnel Boring Machine Jacking/Ram Loads
  • Spreadsheet for adit/junction opening analysis and design
  • Operating Procedure for segment opening temporary support (for adit & cross passage)
  • Spreadsheet for secondary compression index interpretation and settlement calculation
  • BOQ for reclamation
  • Specification for topographic and hydrographic surveys of reclamation and dredging works
  • Checklist for U-loop ground anchor
  • Operating Procedure for RC design using EC2
  • Operating Procedure for design over organic subsoil (peat)
  • Spreadsheet for GFRP design for diaphragm wall
  • Spreadsheet for recharge well design
  • Spreadsheet for cribwall design
  • Operating procedure/spreadsheet for forepoling/pipe umbrella roof design
  • Spreadsheet for pile settlement estimation using T-Z and Q-Z analysis
  • OSHCIM design risk registration form
  • Checklist for mooring pile design

Interested to propose a topic or opportunity to do Joint Industry Project? Send us a message!

Fields marked with an * are required
© Copyright - G&P Professionals Sdn. Bhd.